New Holland Tc33d Parts Manual

This Double Clutch Kit contains SBA320040694 pressure plate 8.50 inch diameter double clutch with 19 tooth 1 3/8 inch center hub, 83986703 drive disc, 8 1/2 inch diameter by 10 spline with 15/16 inch center hub, fiber material, SBA398560340 release bearing outside diameter 3.47 inch by inside diameter 2.16 inch by width of.766 inch, SBA040116001 pilot bearing 1.10 inch OD by.472 inch ID by.472 inch width, and pilot tool,.468 inch pilot, 10 spline, for 15/16 inch hub drive disc, 19 spline 1 3/8 inch on hub for PTO disc. (Part No: SBA320040694K) $1124.69. 12 volt, 40 amp. For tractor models 1320, 1520, 1530, 1620, 1630, 1715, 1720, 1725, 1920, 1925, (2120 1987-2002), 3415, L465, L554, L565, LS140, LS150, LS170, (LX465, LX485, LX565, LX665 1994-1999 with 843 or 844 New Holland engine), TC25, TC25D, TC29, TC29D, TC29DA, TC30, TC33, TC33D, TC33DA, TC35, TC35D, TC35DA, TC40, TC40D, TC40DA, TC45, TC45D, TC45DA.

New Holland Service Repair Workshop Manuals. These are in Downloadable manuals are PDF and are easy to use and will not deteriorate like paper manuals. See more ideas about Holland, Repair manuals and Mazda.

Replaces SBA185046201, SBA185046200. (Part No: SBA185046320) $160.60 Universal Parts and Accessories Category: Accessories / Supplies Accessories / Supplies. This 2 terminal switch has many applications. It is a heavy duty momentary switch, push for on and release for off. It is rated for up to 35 volts.

Uses two screw terminals. The mounting stem is 5/8 inch number 32 thread.

It is 21/32 inch overall length. Check measurements before ordering if using as a universal part. Applications include ether switch, horn button, cold start, starter switch, and manifold heater switch. It replaces 22702, 240962, 242988, 245866, 245936, 70253322, 71191589, 72160068, VT507, 86900358, A30858, O9995AB, T18524, TG07803, TO18117, TO7803, 271179R91, 367678R91, 373611R91, 393209R91, AR46184, AR47373, AR47374, R39554, 189158M91, 767828M91, 105386A, 10A972, 1K7392C, UT2421, 1K7392A, 7A7392.

(Part No: R7994) $11.25 Engine Gaskets. Lucas Assembly Lube (4 oz). Designed to be used as an initial lubricant to metal surfaces. It mixes with any oil and will not plug filters. This product clings to all surfaces and is an excellent rust inhibitor, allowing long term storage for all parts. It's useful wherever tension or torque is applied. Key Benefits are: Use to pre lube camshaft, bearings, lifters and valve train.

Prevents seizing, galling and scuffing perfect for engine lding, super slick and tacky, easy to use, excellent rust inhibitor, excellent for long term storage, contains Zinc, Moly and other extreme pressure additives for maximum protection during engine break-in. (Part No: 10152) $4.65 Engine Parts - Valve Overhaul Kits are located in the Engine Overhaul Kits Section (if available for this tractor). NOTE Engine Pistons and Sleeves. For pistons up to 5 1/2 inches. Cleans grooves of 5/64, 3/32, 1/8, 5/32 and 3/16.

(Part No: B1SB9055) $31.79 Engine Rings - Don't see the correct ring set for your tractor? Give us a call and ask for a Hastings Ring Set (made in USA). We need the following information to correctly find the set you need: 1. Engine size & type (Ex: 233 CID Gas) 2. Number of engine cylinders, 3.

Cylinder bore size, 4. Number and size of compression rings for each piston (Ex: (2) 3/32'), 4. Number and size of oil rings for each piston (Ex: (1) 5/32').

NOTE Exhaust System. Lucas Fuel Treatment is formulated for both gasoline and diesel engines, carbureted or fuel injected. It gives your fuel system what it really needs - a blend of super slick oils and additives with a high detergent action that allows the engine to operate at maximum efficiency. Also, it cleans and lubricates the carburetor and injectors and causes the fuel to burn more thoroughly for increased power and less fuel consumption. Lucas Fuel Treatment should definitely be used in vehicles that require leaded fuel because it actually replaces the benefits of lead in gasoline without causing harmful emissions.

Use it to pass smog tests. Finally, it totally neutralizes the harmful effects of low sulfur diesel fuel.A powerful blend of oils and additives that contain no SOLVENTS. Designed to increase power and fuel mileage and also lower exhaust emissions through a more complete combustion.

(Part No: LU10003) $12.80. This Drawbar Check Chain Kit includes: right hand/left hand anchors, 2 eyelets, 2 chains, 4 clevis with pins, and hardware. Fits: Jubilee, NAA, NAB, 2000 3 Cylinder, 2000 4 cylinder, 2600V, 2N, 3600V, 4000 4 Cylinder, 501, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 2030, 2031, 2100, 2110, 2111, 2120, 2121, 2130, 2131, 2300, 2310, 2600, 2610, 2810, 2910, 3000, 3110, 3120, 3300, 3330, 3600, 3610, [4030, 4130, 4140 (4 cylinder)], 4031, 4040, 4100, 4110, 4120, 4121, 4131, 9N, Industrial: 231, 233, 333, 334, 335, 1801, 1811, 1821, 1841, 1871, 1881, 230A, 3400, 3500, 530A, Dexta, Super Dexta. Replaces: 957E597, 957E596, CBPN598A, NCA597B, NCA596B. (Part No: NCA596B) $28.43. Comes assembled complete with hardware.

Easier hookup, spring loaded locking device. Adjustable top link ball bracket. Includes 7/8 inch mounting pins and adapter bushings, 27-1/4 inches width, 3-1/2 inch x 3-1/2 inch beam. This is ONLY for tractors that have, a three point hitch already installed.

An additional shipping charge of $60 will apply due to the weight of this item. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: HF141101) $178.02. Tail wheel and hub assembly with grease fitting and fork assembly uses 1 1/2 inch diameter shaft. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole.

New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork.

For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Part No: 12269) $176.32. Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly.

OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Part No: BH215) $106.08.

6 inch x 9 inch tail wheel assembly with laminated tire, less hub. 4 inch pilot, 5 bolt holes, 5-1/2 inch bolt circle. 5-1/4 inches wide, 21 inch outside diameter, 74#.

Used mostly on pull Bush Hog models of the following series mowers: 109, 115, 126, 160, 166, 205, 206, 207, 220, 255, 256, 257, 268, 305, 306, 307, 310, 315, 405, 406, 502, 600, 1109, 1115, 1126, 1206, 1207, 1209, 1220, 1226, 1257, 1305, 1306, 1307, 1310, 1315, 1405, 1406, 1600, 2315, 2415, 2510, 2512, 2610, 2614, 2615, 3108, 3209, 3368, 3414, 3610, 4214, 4215, 12610, 12615, 13710, CR14R, CR20F. (Part No: 294) $124.93. 60 inches wide x 65 inches long, molded from virtually indestructible flexible U.V. Stabilized polyethylene, exclusive socket mounting system for torsion bars, no mounting bolts pass through molding. Available in green, white, orange, blue, or red.

Please specify in comments section which color you need. Hardware to mount to your ROPS sold separately. Additional $150.00 shipping due to weight and size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: B257X) $430.31.

45 inches wide x 60 inches long. Molded from virtually indestructible flexible U.V. Stabilized polyethylene, exclusive socket mounting system for torsion bars NO mounting bolts pass through molding.

Available in white, green, orange, blue, and red please specify in comments section which color you prefer. Hardware to mount to your ROPS sold separately.

Additional $150.00 shipping due to weight and size. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: B257XSTD) $374.50. Deluxe Umbrella comes with universal mounting bracket. Four spring steel bows are locked into place with individual spring clips, providing ease of operation and a rigid framework. Frame constructed of tubular steel.

All metal parts are zinc plated for rust resistance. 54 inch square cover is made of durable polyester material. Each corner is double reinforced. AVAILABLE IN RED, YELLOW, ORANGE, WHITE or BLUE. State color desired in comments section of order form when ordering. (Part No: TU56-X) $155.22. A pure petroleum multi-use oil supplement.

Controls noise, heat and wear in manual transmissions and differentials. Number one in the heavy duty and high performance industries. Lucas Oil Stabilizer is a 100% petroleum product formulated to eliminate dry starts and reduce friction, heat and wear in any type of engine. It allows motor oils a higher degree of lubricity which reduces oil consumption and operating temperatures.

Use Lucas Oil Stabilizer in gear oil to stop leaks, reduce operating temperatures and increase the life of the gear oil. Since it is pure petroleum. Key Features Increase oil life at least 50% longer, Reduces oil consumption, Eliminates dry starts, Raises oil pressure, and Increases power and miles per gallon. (Part No: LU10001) $15.12 PTO / Driveline. AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D.

Tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. Beginning Woodcarving Dvd. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch).

Verify length before ordering. (Part No: AB4111WY) $187.82.

AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D.

Tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore.

Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Part No: AB4111K33) $288.01.

****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** Ford Brownish Medium Gray was used for the same applications as TP240Ford Medium Gray.

This is a lighter shade. Since the tractors did not come off the production line all the same, the darker or light shades are completely up to the desires of the customer. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP245SP) $52.66.

****ENTER 1 FOR A CASE OF 6 CANS. NOT SOLD INDIVIDUALLY.**** From Tisco providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics.

PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP447SP) $55.30. This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major.

High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint! Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS.

(Part No: TP240QT) $21.71. This Ford Medium Grey was used from 1948 through 1965 on models 8N, NAA, Jubilee, 600, 700, 800, 900, 501, 601, 701, 801, 901 and Super Major. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Used on 1948 to 1965 tractors. PAINT NOTES: All paint is NON-RETURNABLE. Make sure you order the correct paint!

Paint cannot be shipped to California due to California Regulations. All Paint can only ship GROUND UPS. (Part No: TP240SP) $50.84. Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL.

PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is Black. Additional $30 shipping due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1050ATSP) $82.25.

BLUE Universal application leatherette suspension seat. For most compact, agricultural and industrial tractors. Adjustable base for 5 different mounting angles, internal suspension weight adjustment, special slotted base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, adjustable slide track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLUE. Add $15 additional shipping per seat due to size and weight.

IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1060ATSP) $82.25. Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors. Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track.

Best Automated Software Testing Tools. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is BLACK. (Part No: TS1075ATSP) $80.04. **YELLOW** Universal Application Leatherette Suspension seat. For most Compact, Agricultural and Industrial Tractors.

Adjustable base for 5 different mounting angles, Internal Suspension Weight Adjustment, Special Slotted Base for mounting holes adjustments of approximately 2-1-2 inches forward/rear, Adjustable Slide Track. IMPORTANT: THESE SEATS FIT MOST TRACTORS, BUT NOT ALL. PLEASE LOOK CLOSELY AT THE DIMENSIONS ON THE PICTURE BEFORE ORDERING TO BE SURE IT WILL FIT YOUR TRACTOR. Color is John Deere Yellow. Add $15.00 additional shipping due to weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: TS1040ATSP) $88.39 Sheet Metal / Body Parts.

This is a 5.5 inch x 16 inch Front Wheel Rim. It has a pilot hole of 4.625 inches.

It uses 6 bolts in a 6 inch bolt pattern. Back-spacing is 4.75 inches. Capacity of 3500 lbs based on 20 MPH max speed. Verify size of old rim before ordering. Add $25 additional shipping per rim due to size and weight. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED.

Replaces AL82488, A38404, C7NN1007J, D2NN1007N, D2NN1007S, D8NN1007BA, E1ADDN1015B, E1ADKN1015A, E6NN1007BA, G57046, K914312, K921475, K947941, VPH6001, 1660769M1, 1678319M91, 1678319M92, 1691618M92, 1691618R92, 1883333M92, 3114166R91, 509893M1, 509893M91, 57512110, 8, 751734R91, 82005056, 83900159, 83954658, 83960327, 9A306 (Part No: FW55166) $59.27. Tractor is embroidered on the hat with words 'Ford 8N' (Part No: FD8N) $19.95 Call 800-853-2651 to Order Or Click the 'Add to Cart' Button [] [] [] Customer Service Monday - Friday 9:00-6:30pm EST Order online anytime! Your Shopping is YESTERDAY's TRACTORS has been a leading tractor parts supplier on the internet since 1995. Join thousands of happy customers who have purchased parts and more for their antique tractor from us!

Copyright © 1997-2015 Yesterday's Tractor Co. Antique Tractor Headquarters All Rights Reserved TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. Products and within the Yesterday's Tractor Co.

Websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.